準備工作

preparation

確認門的尺寸、款式和開啟方式等是否符合要求，檢查不銹鋼玻璃門及配件是否齊全，有無損壞。

Confirm whether the size, style, and opening method of the door meet the requirements, and check whether the stainless steel glass door and accessories are complete and undamaged.

準備好安裝所需的工具，如電鉆、螺絲刀、扳手、水平尺、玻璃膠槍等，以及必要的材料，如膨脹螺栓、密封膠、墊片等。

Prepare the necessary tools for installation, such as drill, screwdriver, wrench, level ruler, glass glue gun, as well as necessary materials such as expansion bolts, sealant, gaskets, etc.

清理安裝現場，確保地面和墻面平整、干凈，無雜物和障礙物。

Clean up the installation site to ensure that the ground and walls are flat, clean, and free of debris and obstacles.

定位與劃線

Positioning and marking

根據設計要求，在地面和墻面上確定門的安裝位置，并使用墨線或激光水平儀等工具進行劃線，標記出門框的輪廓和固定點的位置。

According to the design requirements, determine the installation position of the door on the ground and walls, and use tools such as ink lines or laser level to mark the outline of the door frame and the position of the fixing points.

檢查劃線是否水平、垂直，確保門安裝后處于正確的位置。

Check whether the marking is horizontal and vertical, and ensure that the door is in the correct position after installation.

安裝門框

Install door frame

將不銹鋼門框按照劃線位置放置在地面上，使用水平尺和垂直尺進行調整，使其達到水平和垂直狀態。如有偏差，可通過在門框底部或側面墊墊片的方式進行調整。

Place the stainless steel door frame on the ground according to the marked position, and adjust it with a horizontal and vertical ruler to achieve a horizontal and vertical state. If there is any deviation, it can be adjusted by placing shims at the bottom or side of the door frame.

在門框的固定點位置鉆孔，使用膨脹螺栓將門框固定在地面和墻面上。擰緊膨脹螺栓時，要注意力度均勻，避免門框變形。

Drill holes at the fixing points of the door frame and use expansion bolts to fix the door frame to the ground and wall. When tightening the expansion bolt, pay attention to even force to avoid deformation of the door frame.

安裝門框的連接件和密封膠條，確保門框與墻體之間的密封性能，防止雨水和灰塵滲入。

Install the connectors and sealing strips of the door frame to ensure the sealing performance between the door frame and the wall, preventing rainwater and dust from infiltrating.

安裝玻璃

install glass

檢查玻璃的尺寸和質量，確保其符合門的規格要求。將玻璃小心地搬運到門框前，準備安裝。

Check the size and quality of the glass to ensure it meets the specifications of the door. Carefully transport the glass to the door frame and prepare for installation.

如果是單塊玻璃門，可直接將玻璃放入門框內，使用玻璃膠或其他固定材料將玻璃固定在門框上。如果是雙玻璃或多層玻璃門，需要先安裝玻璃間隔條，再將玻璃逐塊放入門框，并進行固定。

If it is a single glass door, the glass can be directly placed inside the door frame and fixed to the door frame using glass glue or other fixing materials. If it is a double glass or multi-layer glass door, it is necessary to install glass spacers first, then place the glass pieces into the door frame one by one and fix them.

在玻璃與門框之間的縫隙中注入密封膠，以增強密封性能和防水性能。使用膠槍將密封膠均勻地涂抹在縫隙中，然后用刮刀將多余的膠刮平，使密封膠表面光滑。

Inject sealant into the gap between the glass and the door frame to enhance sealing and waterproofing performance. Use a glue gun to evenly apply sealant in the gaps, and then use a scraper to smooth out the excess sealant to make the surface of the sealant smooth.

安裝門五金配件

Install door hardware accessories

安裝門鎖，根據門鎖的類型和安裝要求，在門和門框上鉆孔，安裝鎖芯、鎖體和鎖舌等部件。確保門鎖安裝牢固，開關靈活。

Install the door lock, drill holes in the door and door frame according to the type and installation requirements of the lock, and install components such as the lock cylinder, lock body, and lock tongue. Ensure that the door lock is securely installed and the switch is flexible.

安裝合頁，在門和門框上分別安裝合頁，使用螺絲將合頁固定。安裝合頁時要注意位置準確，確保門能夠平穩地開啟和關閉。

Install hinges, install hinges on the door and door frame respectively, and fix the hinges with screws. When installing hinges, pay attention to accurate positioning to ensure that the door can open and close smoothly.

根據需要安裝其他五金配件，如門拉手、門吸等。門拉手要安裝牢固，方便使用；門吸要安裝在合適的位置，能夠有效地固定門的開啟狀態。

Install other hardware accessories as needed, such as door handles, door stops, etc. The door handle should be installed firmly and easy to use; The door stopper should be installed in a suitable position to effectively fix the open state of the door.

調試與檢查

Debugging and Inspection

安裝完成后，對不銹鋼玻璃門進行調試。檢查門的開啟和關閉是否順暢，有無卡頓、異響或晃動現象。如果發現問題，及時調整合頁、門鎖等部件，直到門的開關性能良好。

After installation, debug the stainless steel glass door. Check whether the opening and closing of the door are smooth, and whether there is any jamming, abnormal noise or shaking phenomenon. If any problems are found, adjust the hinges, door locks, and other components in a timely manner until the door's opening and closing performance is good.

檢查玻璃的安裝是否牢固，密封膠是否均勻、無漏洞。檢查門鎖、門拉手等五金配件的安裝是否牢固，使用是否方便。

Check whether the installation of the glass is firm, whether the sealant is uniform and leak free. Check whether the installation of hardware accessories such as door locks and door handles is secure and whether they are easy to use.

最后，清理安裝現場，將剩余的材料和工具整理歸位。

Finally, clean up the installation site and organize the remaining materials and tools back into their designated locations.

本文由山東不銹鋼玻璃門友情奉獻.更多有關的知識請點擊:http://www.sdshd.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is a friendly contribution from Shandong Stainless Steel Glass Door For more information, please click: We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message